Open circuit voltage (V): 58. Nominal input current (A): 13.4. Setting range of the output current (A): 45 - 130A.
Output voltage (V): 15.5 - 18.5. Duty cycle: 20% at 90A. Power factor:> 0.7. Welding wire diameter: 0.8mm/0.9mm.
Dimensions (L x W x H): 318 x 135 x 240mm. 1 MIG15 welding torch with 2m. 1 Flux cored wire of 0.5kg, 0.8mm, without gas. Quick and easy welding wire installation.
No wire feed wheel is required and the wire can be fed directly through the installation of the welding wire, which is very convenient and time-saving. Support 0.8mm and 0.9mm welding wire, we are equipped with 0.8mm welding wire, so you can use it when you receive the goods (Note: 0.9mm welding wire not equipped).
This machine supports the use of gas-free welding, which is very convenient, relieves the gas cylinders and does not have to worry about the inconvenience of outside welding. Can be welded to a thickness greater than or equal to 0.5mm, suitable for welding carbon steel and low carbon steel. No gas is required, it does not pollute the environment and also protects the respiratory tract from damage.
The fan has a sleep function and may not spin after turning it on, which is normal. The machine is equipped with a heat dissipation and overheating protection function which, if the machine is running too hard, activates the rear fan to dissipate the heat from the internal parts of the machine. A smarter design will make your machine last longer. We have a solid service system.
We provide 3 years product quality service, 24 hour online service to answer your question. Our factory's production process has been checked layer by layer to ensure that each machine is performing well for you. How to install the belt. Take the parts of the belt and prepare to install the belt on the welder.
Thread the belt on both sides of the machine. Adjust the belt length to your needs. The weight of the welding machine only 5.4 kg, small. It is very suitable for carrying on the shoulder to continue the welding process.
The belt is soft and adjusts to the angle according to the shoulder and the shoulder will not hurt even after a long time. Self-protected welding with flux cored wire, easy welding. Standardization of the integration of EMC card and motherboard. The wire feed speed and voltage are automatically adjusted and the current / voltage is automatically set to the best value. Durable, fan quiet, overheating / overcurrent / overvoltage protection.
The welding gun is an integrated MIG15 torch with a length of 2 meters. The power indicator does not light up, the fan does not work and the welding current is missing. Make sure the air switch is closed. Check that the wire mesh is working.Some of the (four) heat variable resistors on the power panel are damaged. In this case the general DC14V relay is open or the connections are poorly connected. Power panel (bottom) is damaged, DC 130V voltage cannot be output. (1) The silicone bridge is broken or the silicone bridge connector has poor contact. (2) The power panel has burned out. (3) Check whether the contact and the plug-in cable from the air switch to the power panel have poor contact, check whether the contact and the plug-in cable from the power panel to the IGBT board are reliably connected. The auxiliary power supply to the control center is defective. Power indicator is on, fan is running, no solder emissions. Check if all types of cables between machines are making poor contact.
The output connector is defective. The output connector is defective or not properly connected.The control circuit is interrupted. The operating indicator lights up, the fan is running, the fault indicator lights up.
It may be overheating protection, turn off the power first, then turn it on again after the abnormal indicator goes out. Maybe it's overheating protection, please wait 2-3 minutes. Possibly the circuit of the inverter is interrupted, unplug the mains plug of the main transformer, which is located on the IGBT board, and open the machine again. 1 If the fault indicator is still on, some of the field transistors on the IGBT board are damaged, locate them and replace with the same model.2 If the abnormal indicator does not light up. A: The central PCB transformer may be damaged, measure the volume of the inductor and the volume Q of the main transformer across the inductor bridge. If the volume is too low, replace it. The transformer secondary rectifier tube may be damaged, correct the problem and replace the rectifier tub.
Item Processing Time: The processing time for a specific order depends on the product type and stock status. Processing time will be postponed during holidays or weekends! So please test whether the product works well as soon as you receive it! 7 days no reason to return.Return must include all original package and accesorries, item must in good condition. Defective item: Please contact our customer service to explain the product problem before returning the goods. We will provide 24-hour online service and lift-time technology support for every valued customer! First-class talents and advanced equipment.
Mart Design with full digital control, Constant voltage and synergic adjustment control. Ully implement the ISO9001:2008 quality management system. Each Machine with 100% QC Test, Life Test and Welding Function Test, Drop test and Dust test! Over 10 years factory control system focus on the welding field.
Please be patient when contacting us, all messages will be replied within 24 hours. Please let us know immediately if a package is damaged upon arrival. Fortune 500 listed companies in the world. Choose REBOOT, just WELD and CUT.
Output current adjustment range(A). 15.5 - 18.5. Type of the wire feeder. Weight without wire roller(kg). This item is in the category "Business, Office & Industrial\CNC, Metalworking & Manufacturing\Welding & Soldering Equipment\Welding Equipment & Accessories\Welders, Cutters & Torches\MIG Welders".
The seller is "mirthstore" and is located in this country: GB. This item can be shipped to United Kingdom.