MIG 130 IGBT Inverter DC Welder Gasless Flux Core Wire No Gas Welding Machine UK

MIG 130 IGBT Inverter DC Welder Gasless Flux Core Wire No Gas Welding Machine UK
MIG 130 IGBT Inverter DC Welder Gasless Flux Core Wire No Gas Welding Machine UK
MIG 130 IGBT Inverter DC Welder Gasless Flux Core Wire No Gas Welding Machine UK
MIG 130 IGBT Inverter DC Welder Gasless Flux Core Wire No Gas Welding Machine UK
MIG 130 IGBT Inverter DC Welder Gasless Flux Core Wire No Gas Welding Machine UK
MIG 130 IGBT Inverter DC Welder Gasless Flux Core Wire No Gas Welding Machine UK
MIG 130 IGBT Inverter DC Welder Gasless Flux Core Wire No Gas Welding Machine UK
MIG 130 IGBT Inverter DC Welder Gasless Flux Core Wire No Gas Welding Machine UK
MIG 130 IGBT Inverter DC Welder Gasless Flux Core Wire No Gas Welding Machine UK
MIG 130 IGBT Inverter DC Welder Gasless Flux Core Wire No Gas Welding Machine UK
MIG 130 IGBT Inverter DC Welder Gasless Flux Core Wire No Gas Welding Machine UK
MIG 130 IGBT Inverter DC Welder Gasless Flux Core Wire No Gas Welding Machine UK

MIG 130 IGBT Inverter DC Welder Gasless Flux Core Wire No Gas Welding Machine UK
MIG-130 Welder Gasless No Gas Flux 230V Welding Machine + Wire Reel Mask Kits. FLUXWIRE WELDING MACHINE FOR FLUX (NO GAS) WELDING. HT IN THE JOB SITE. Input Power(Kva):3.6.

No load voltage(V):37. Welding wire dia(mm):0.6-0.9. ARC WELDING CAN BE DANGEROUS.

THIS WELDING MACHINE MUST BE CONNECTED TO A POWER SOURCE IN ACCORDANCE WITH APPLIANCE ELECTRICAL CODES. FOR SAFETY TURN OFF AND UNPLUG MACHINE WHEN INSTALLING NEW WIRE SPOOL, ADJUSTING WIRE TENSION ROLLER OR REPLACING CONTACT TIP. THE GAS NOZZLE MUST ALWAYS BE INSTALLED WHEN WELDING-DO NOT WELD WITHOUT THE GAS NOZZLE IN PLACE. THE CONTACT TIP IS ELECTRICALLY "HOT" AND IF IT CONTACTS THE GROUNDED WORK PIECE IT WILL CAUSE DAMAGE.

ALL INSTALLATION, MAINTENANCE, REPAIR OPERATION OF THIS EQUIPMENT SHOULD BE PREFORMED BY QUALIFIED TECHNICIANS IN ACCORDANCE WITH NATIONAL, STATE AND LOCAL CODES. DISCONNECT FROM POWER SOURCE BEFORE ASSEMBLING. DISASSEMBLE OR MAINTENANCE OF THE TORCH OR CONTACT TIP OR CHANGING WIRE SPOOLS. DISCONNECT FROM POWER SOURCE BEFORE ASSEMBLING, DISASSEMBLY OR MAINTENANCE OF THE TORCH OR CONTACT TIP OR CHANGING WIRE SPOOLS. FUMES AND WELDING GASES CAN BE DANGEROUS.

WELDING SPARKS CAN CAUSE FIRE OR EXPLOSION. ELECTROMAGNETIC FIELDS MAY BE DANGEROUS. PLS BE REMINDED TO WEAR ALL PROTECTION DEVICES BEFORE WELDING IN A SAFE PLACE. 1:MIG130 welder is AC of no gas (flux) function. It could weld max 1kgs welding wire.

Please be reminded to assemble the correct size of wire in usage. 2:When torch nozzle touch the workpiece, there would be arc starting. 3:The contact tip is a consumable item and must be replaced when the bore becomes enlarged or oval. The contact tip MUST be kept free from spatter.

4:The Nozzle must also be kept clean and free from spatter. Build-up of spatter inside the nozzle can cause a short circuit at the contact tip which will result in expensive machine repairs. To keep the contact tip free from spatter. 5: Should the welder become overheated due to prolonged use beyond the stated duty cycle the thermal protection will cause the welder to cut out and the orange light on the front panel will illuminate.

Wait for fifteen minutes for the welder to cool down at which time it will reconnect automatically. Burning holes in work piece. Welder does not operate(mains indicator not lit, no arc produced). Welder does not operate with trigger pressed. Check torch trigger and it's connections.

Thermal overload cut out-allow to cool. Check pcb correct or not-replace.

Incorrect size of contact tip for wire. Supply fuse is trip off. Input current is too big, suggest to change to bigger fuse to 30A. Does not feed the wire. Check the instalation, make sure wire is properly installed according to the manual guide.

Pls feed the wire by hand more length, may easy feed out. Press the torch trigger more strength and more times.

Take off the contact tip and nozzel and not put the wire first, see if the wire roll turn. PCB have the problem, change a PCB.

Our shop based on the professional home essentials and garden tools store. Your satisfaction is our goal. Happy online Shopping, Thank you! We are not responsible for any wrong or undeliverable addresses. We stand behind every product we sell. Your better comments will be an encouragement for us to offer the better quality and the better service in future. We shall try our best to solve your problem to your satisfaction. This item is in the category "Business, Office & Industrial\CNC, Metalworking & Manufacturing\Welding & Soldering Equipment\Welding Equipment & Accessories\Welders, Cutters & Torches\MIG Welders".

The seller is "electronic1star" and is located in this country: GB. This item can be shipped to United Kingdom.


MIG 130 IGBT Inverter DC Welder Gasless Flux Core Wire No Gas Welding Machine UK


Mig Welder Inverter  Sitemap  Contact  Privacy Policy  Terms of Use